+86-317-4168868

What should be paid attention to in the design of ton bags?

Oct 30, 2022

Ton bags are generally made of polypropylene, polyethylene and other polyester fibers, which can be widely used in the packaging of various powder, granular and block items such as chemicals, building materials, plastics, and minerals. ideal supplies. Therefore, special attention should be paid to its design process. 

1. Check the selection of base fabrics

When designing a ton bag, first clarify the weight of the loaded goods, and determine the volume of the ton bag according to the specific gravity of the packaged material. It also depends on whether the loaded material is a sharp and hard block material. In the case of sharpness, it is recommended that the base fabric should be thicker when designing the ton bag, and on the contrary, it can be thinner. In the actual design, for a ton bag with a load of 500kg, the base fabric is generally (150-170) G/m2, the longitudinal and transverse tensile strength of the base fabric is (1470-1700) N/5cm, and the elongation is 20-35%. Big bags with a load of more than 1000kg. The base fabric is generally selected (170210) G/m2, the longitudinal and transverse tensile strength of the base fabric is (1700-2000) N/5cm, and the elongation is 20"35%. To improve the strength of the filament, the ton bag must increase the strength of the base fabric to ensure the strength of the base fabric. The tensile strength of the flat wire. The relative strength of the flat wire should be above 0.4N/Tex, and the elongation rate should be 15-30%. In the actual production and processing process, the amount of filler batchmate should be strictly controlled, generally around 2%. Adding too much batchmate or adding recycled materials will reduce the strength of the base fabric. Therefore, the quality of the raw materials should be strictly controlled, and the ton bag should use the drawing raw materials produced by regular manufacturers whose melt index reaches the national standard.

2. Select the material of the sling

In the design of ton bags, the selection of sling materials is very important. The national standard clearly stipulates a safety factor of 1:6. In the actual design of the ton bag, one must consider the loss of the strength of the sling during the sewing process; the other must consider the hoisting method. It is required that the sling must meet the weaving density requirements. When designing a sling for the ton bag, two loops or four loops can be used to increase the tensile strength.

3. Add additives to prolong the service life

In order to improve the anti-aging ability of plastic ton bags under sunlight, a certain amount of anti-violet agent and stabilizer should be added in the flat yarn drawing process. According to the length of the service life of the ton bag (half a year or a year), the amount of addition is determined, generally between (0.1-3)%. Some enterprises add anti-aging batchmate made of stabilizer, anti-violet agent and other additives, and the effect is also very good.

4. Structural design

When designing the ton bag structure, the national standard stipulates that the strength of the waistband should be more than twice the strength of the base fabric, but the actual design effect is not good, because the strength of the base fabric and the waistband are inconsistent, causing the base fabric to crack first. In the design, the waistband and the base cloth are made of the same strength base cloth material, which can avoid this problem.

5. Sewing process design

In addition to the sewing requirements specified in the national standard, the aging resistance of the suture and the effect of the sewing on the tensile strength of the base fabric should also be considered for the ton bag. When packaging powder, poisonous, or contaminated items, the first thing to do is to solve the problem of air tightness. Therefore, in the actual design, the ton bag is sewn with thick thread and fine needle or non-woven fabric and base fabric to improve the sealing performance. In addition, when sewing big bags, it is required that the stitching thread should be made of polyester thread with a strength of more than 18kg to ensure that its sewing strength meets the national standard.

6. Design of inlet and outlet

The national standard stipulates that the longitudinal and transverse tensile strength of the base fabric at the inlet and outlet is 3828N/650mm, but in the actual design, due to the large tensile force at the outlet, it can be higher, and the strength of the inlet can be lower, and the film is generally used. Base cloth (90-100) S/m2.

7. Other factors

In the process of design and experiment, the ton bag with bottom hanging structure without feeding port can generally meet the safety factor requirements stipulated by the national standard. However, the strength of the ton bag with the discharge port is generally not up to the standard, which requires consideration of increasing the bottom opening strength in the design. 


Send Inquiry